how to start a gas fireplace

Locate the metal keyhole near the fireplace. The good news is they can be swapped out without replacing the whole fireplace.

How To Light The Pilot On A Gas Fireplace Fireplace Lighting Gas Fireplace Gas Fireplace Insert

Before the remote can work the master switch must be in the on position on the fireplace.

. Once the burner is lit insert the key and turn it. Afterward our study went on with the heatilator gas fireplace manual 1996. Arrange the logs on the fireplace grate. Manufactured fireplaces are made with sheet metal or glass fire boxes.

If you begin to detect a strong odor or notice white smoke coming from the fireplace itself dont worry. The pilot light will remain on to allow you to do this. Insert the end of the key into the keyhole until it. Once the pilot has been lit hold the valve control knob in position for 1 minute and then slowly position the valve control so.

Make sure the flue is open before you light your fire. First turn your gas fireplaces knob from the Off to the Pilot position. Remove the outer cover of the fireplace to access the burner. How to start a gas fireplace for the first time.

On some gas fireplaces this alone may start the pilot light. How to start a gas fireplace with remote. This will allow you to push the knob in which manually releases the flow of gas to the pilot. After you remove the screen use a match or lighter to light the burner and be careful to not burn yourself.

Light the gas starter using your match or lighter immediately. Turn the control knob to the on position. How do I start an old gas fireplace. Turn the control dial from the Off position to the Pilot position through any spark clicks.

Put the pilot light starter in the ignite position and press down on the knob firmly. See your owners manual for specifics. First take a look at the main valve to confirm that the gas is on. How to easily light a remote control fireplace that wont start gas fireplace wont light fixedsimple steps to get your fireplace going again to warm.

Light your long match or have your long lighter in your hand and ready to go. On off and pilot. Place a long lighter next to the burner and pull the fuel trigger. Allow room temperature air to flow through the fireplace and up the.

Depending on how long its been since the gas fireplace was last used ignition may take several attempts before igniting. 2 Step-by-step Instructions 21 Step 1. Once this is done you will now be able to easily switch your gas fireplace on or off using either a remote control device or a switch on the wall. Grab your gas key but dont turn on the gas yet.

How to Start a Gas Fireplace Todays modern gas fireplaces are typically controlled with a remote control meaning starting your gas fireplace is as easy as pressing the on button on your remote. How to start a gas fireplace. How to Start a Gas Fireplace with a Key Step 1. You have to remove the gas logs and its gas burner pipe entirely and replace it with a real gas starter pipe that you can purchase from a stove shop or a hardware store.

Do not use flammable liquids to start a fire. What you have is a masonry fireplace with a set of gas logs stuck in them. Push in the pilot knob which will then manually send gas into the system. Other gas fireplaces may have a separate spark ignitor button that needs to be pressed alongside the dial.

Most gas fireplaces have a standing pilot light which is a small flame that burns even when you arent using the fireplace. This small round slot could be located on the floor in front of. Now while holding the pilot knob in push the igniter button in once every second until the pilot is lit. Some fireplaces can be controlled with a key valve so you will need the key to turn the valve.

Then you can burn wood in your fireplace again. Use a flashlight to look inside the. The pilot knob has three positions. Use the gas key to turn the gas valve a quarter turn.

Turn the key in the slot to. Push the igniter button once every second until it lights. You can also use a lit match You may need an assistant if the slot is out of reach from the burner. Without a remote there will typically be an ignition button on the control panel of the fireplace.

Correcting the air flow. Make sure your damper is open and nothing is blocking your chimney. Move the pilot knob to the pilot position.

How To Start A Gas Fireplace Quickly Gas Fireplace Fireplace Gas